Questions and answers

How do I setup my tp-link wireless router modem?

by Admin

How do I setup my tp-link wireless router modem?

Power on your router and computer first and then modem.

  1. Log into the router’s web-based management page.
  2. Configure WAN Connection Type.
  3. Enter your PPPoE username and password which are provided by your ISP.
  4. Click Save to save your settings, then the router will connect to Internet after a while.

How do I use TP-LINK TD w8961n as wireless repeater?

Step 1 Log into TD-W8961ND’s management page. If you are not sure about how to do this, please click here. Step 2 On the top-side menu, click Interface Setup->Wireless, change the channel to a fixed one, like 4. Step 3 Check the SSID of the main TD-W8961ND, and set the wireless security for it.

How do I connect my wireless access point to my ADSL modem?

Work

  1. Introduction.
  2. 1Connect the Ethernet port of your cable modem or router to your wireless access point’s Internet (or WAN) port using an Ethernet network cable.
  3. 2Connect your wireless access point to your computer using an Ethernet network cable.
  4. 3Turn on your DSL or cable modem and wait about two minutes.

How do I reset my TP-LINK TD W8951ND?

To reset the TP-LINK TD-W8951ND to its default settings, you have to do the following steps:

  1. Put router into operation.
  2. Press RESET button and hold for at least 5 seconds.
  3. Device restarts automatically.
  4. Router has been reset to factory settings.

How do I access my tp-link modem?

Log into the router using tplinkmodem.net or the default IP address 192.168. 1.1. The default login username and password are both admin (all lower case). If needed, you may refer to How to log into the web-based interface of the AC VDSL/ADSL Modem Router for more detailed information.

How can I convert my TP-Link ADSL modem to wireless router?

Go to DHCP>DHCP Settings and select Disable the DHCP Server. Select Save. Go to System Tools>Reboot and select Reboot to reboot the device. Use an Ethernet cable to connect the main router to your TP-Link N router through their LAN ports (any LAN ports may be used).

How do I add wireless access points?

Simply connect the access point to one of the ports of your existing wired/wireless router then configure the access point’s wireless settings.

  1. Open the access point’s web-based setup page by entering the default IP Address “192.168.
  2. On the web-based setup page, click on Wireless.
  3. Enter the Network Name (SSID).

How do I default my TP-Link Router?

With the Router powered on, press and hold the WPS/RESET button (more than 10 seconds) until the SYS LED becomes quick-flash from slow-flash. Then release the button and wait the Router to reboot to its factory default settings.

How do I activate my TP Link Router?

  1. Step 1: install the TP-Link Tether app.
  2. Step 2: connect your router.
  3. Step 3: connect to the Internet with the new router.
  4. Step 4: open the Tether app and log in.
  5. Step 5: adjust router settings.
  6. Step 6: save everything and connect to the Internet.
  7. Step 7: link to your TP-Link Cloud.

How to reset a TP-Link td-w8951nd configuration support?

In the browser’s address bar, enter the IP address for the modem interface page: 192.168.1.1 If the modem was previously configured for someone, the password would be the previous user’s DSL password. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back.

Is the td-w8951nd a 3 in 1 router?

As a 3-in-1 device, the TD-W8951ND combines the functions of a high speed DSL modem, a 4-Port 10/100Mbps NAT router and a wireless N access point. Using a DSL enabled telephone line the TD-W8951ND could establish a high-speed ADSL2+ Internet connection.

What should I do before upgrading to td-w8951nd?

It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade. Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade. 1.Added 6RD content to help information.

How to avoid wireless disconnect with TP-Link?

To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device. It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.